Professional
Two-Component
Pneumatic Epoxy Injection Machine

Complete Set,
including all pressure hoses,
applicator and Static Mixers

- 800 PSI (40% more than previous model)
- 2:1 OR 1:1 MIX. RATIOS
- 3" DIAMETER AIR-CYLINDER
- EASY TO CLEAN
- POSITIVE DISPLACEMENT PISTON
- ONE KNOB OPERATION
- PRESSURE LINES INCLUDED
- COMPACT AND LIGHTWEIGHT
- RUGGED CONSTRUCTION
- VERY AFFORDABLE
- EASY TO USE
- RELIABLE

Professional injection equipment can be affordable for any contractor. Our latest example is the PA3000 injection machine which combines high quality with a very competitive price.

The new PA 3000 epoxy injection pump is an improved and more powerful machine that evolved from our legendary PA 2500 injection pump.

The PA3000 features a three inch air cylinder. The larger air cylinder increases power by 40% for pressures up to 800 psi. The higher injection pressures allow for better performance with thicker resins and with all materials at lower temperatures.
The tanks are now unitized, without a separate cart. All four caster wheels have breaks and the machine is considerably more mobile. The pump is available set-up with 2:1 or 1:1 mixing ratio. With purchase of a separate piston/cylinder unit mixing ratios can be easily interchanged.

The PA 3000 is a powerful injection pump for professional liquid resin injection into structural concrete cracks. Its unique design sets new standards for performance and features. This complete package includes material reservoirs, the applicator with static mixer and a 20' set of high pressure hoses. The machine is furnished with male hose adapters and push-in tube connectors for the pneumatic lines. Hoses are available in a variety of sizes. We supply surface ports in several sizes. Please refer to our data sheet on Multiple Port Injection System for further information.

Standard Ratios 1:1 or 2:1
Material Flow Rate Approx. 0.4 GPM
Dimensions 14" x 22" x 29" high
Weight 60lb.
Tank Capacities 3 1/3 gal ea.
Material Viscosity Pourable
Outlet Pressure 15 - 800 psi
Air Requirements 1CFM 40 -120psi


DATA SHEET

Affordable
Professional
Joint Sealer Machine
For

Epoxy, Polyurea, Polyurethane

New Optional Accessories:

- Heater Bands

- Battery Operation / Inverter

New And Improved Model for 2006 Offers

Advanced Design Features

- Pumps Many Epoxies, Polyurethanes & Polyureas
- Very Affordable And Reliable
- Pumps Thicker Materials
- Rugged Construction And Easy To Use
- Volume Adjustable Dispenser
- Extra Lightweight Aluminum Dispenser
- Stainless Steel Tanks
- Gear Driven For Easy Ratio Changes
- Compact And Lightweight Unit
- Unit Mounted On 'EZ-Ride' Coasters
- Complete Set With Hoses And Applicator
- Easy To Clean
- Heater Bands Optional
- Batterie/ Inverter Use Optional

Also:

- Heater Bands Available

- Battery Operation Possible With Inverter

- Cordless Operation With Generator

SealBoss 6500 QuickFix Polyurea Joint Sealer

SealBoss 6000 QuickFix Spall Repair

Weight: 165 lbs. dry Height: 38-1/2”, Width: 27”, Length: 30”
Motor: 1/2HP DC Gear motor w/separate heat sink, RPM: 0 - 500,
Volts: 90-130, Torque: 202 In. Lbs., Amps: 5.5
Pumps: Cast iron internal rotary gear pumps w/steel fitted rotor gear
Tanks: 5 gallon, 14 gauge 304 stainless steel (ss) tanks w/ss lids, w/custom welded ss mounting nipples for ss suction line strainers and pump mounts, attached to frame with ss worm gear clamps
Power: 110 volt
Hoses: 3/8” x 14.5’ Nylon braided hoses coupled with a protective sleeve
Wheels: 6” non marring gray balloon cushion wheels for easy roll over of cords and debris, swivel wheels have brakes
Dispensing
Unit: Extended lightweight handle with a dual port manifold,
on/off switch and speed control knob
Viscosity: 50 – 2,500 cps, viscosit y is only one of many factors to determine suitability and compatibility
Flow Rate: Up to 2 gallons per minute
Ratios: 1 – 1 ratio, easily geared to other ratios

Picture left:

Pump shown with optional Heater Bands

Please contact a representative for detailed information and limitations. Specific product sheet data and MSDS of product to be intended for use wil help you to determine the suitability.

Due to the nature of a dispensing machine like the JointMaster Pro2, user shall rely on his or her own information and tests to determine suitability of the product for the intended use and user assumes all risk and liability resulting from his or her use of the product. Nothing contained in any materials supplied or distributed by WEBAC Corp. relieves the user of the obligation to read and follow the warnings and instruction for each WEBAC Corp. product as set forth in the current Technical Data Sheet, product label and Material Safety Data Sheet prior to product use. Webac Corp. warrants its products to be free of manufacturing defects. Seller’s and manufacturer’s sole responsibility shall be to replace that portion of the product of the manufacturer which proves to be defective.

There are no other warranties by WEBAC Corp. of any nature whatsoever expressed or implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. WEBAC Corp. specifically does not take back or restock any used equipment. WEBAC Corp. does not apply credit for used equipment.

'Strap On' Heater Bands

are for use in colder climates, freezer warehouses and also to warm high viscosity (thicker) products to increase ease of flow.